Plumbing for Beginners: The Essentials for Installing a Bathtub
Plumbing for Beginners: The Essentials for Installing a Bathtub
Blog Article
We have stumbled upon this great article about Tools You Need to Install a New Bathtub directly below on the internet and think it made good sense to talk about it with you in this article.
Setting up a bath tub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably challenging job. If the old tub is easily accessible, the job can move rapidly; if you have to open up a wall surface to eliminate the old tub as well as place the brand-new tub, the task is much harder. In either case, the job is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and also set in the new one. Make sure you have actually certified on your own for the task and also are comfortable trying it. Instead of employing a specialist to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This post will help you set up a new bathtub in your restroom if you have already bought a brand-new bathtub and also don't require to change the arrangement of your previous water system pipes.
Your tools and also material list should make up the following:
Getting ready for the Installment
To start with, the supporting frame provided with the bath needs to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to ensure that if the tap features a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps device to stop pressure on the tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final position.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be quite problematic because of the restricted gain access to that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel all set for the staying water that will certainly come from the pipes. Once the supply pipes have been gotten rid of, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from transforming throughout this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before proceeding to fit the brand-new taps, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Using both wooden boards under its feet, position the bathtub in the called for placement. The wood boards are useful in evenly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bathtub till the level reads degree.
To mount taps, fit all-time low of the outermost flexible tap connector to the appropriate supply pipe by making a compression join; then do the same for the various other faucet.
Switch on the water supply as well as inspect all joints as well as brand-new pipework for leaks and tighten them if required. Fill the bath tub as well as likewise inspect the overflow outlet as well as the regular outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the maker's user's manual. Tiling and sealing around the bath tub should wait up until the tub has been made use of a minimum of when as this will settle it into its last setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and the other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin ensuring that the washers are in location between the faucet as well as the sink. Protect the faucet in place with the producer offered backnut. Once the tap is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous kind should be attached to the faucet finishes first, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a rigid seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, leading to difficulties with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and cartridges, and also can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched paper or soft rope. Remember to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can split relatively early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that blog entry about How to Install a Bathtub Yourself while doing a lookup on the search engines. Enjoyed reading our write-up? Please share it. Help someone else discover it. Kudos for your time. Visit again soon.
Access top-rated emergency plumbers. Report this page